Grant: Discovery Grants Program - Individual
University of British Columbia
$20,000.00
Development of discrete element models for continious rotary drum drying and blending for osb
FY 2010-11
Summary
Oriented Strand Board (OSB) is the dominant structural panel in today's North American residential construction market. These strand-based wood products can be found everywhere from sheathing on exterior walls to the headers used to span garage door openings and specialty studs used behind kitchen cabinets.
OSB is made from thin strands that are first dried in a Rotary Drum Dryer (RDDr) and then coated with resin in a Rotary Drum Blender (RDB). Both RDDr and the RDB are, as their names imply, large drums that rotate about their long axis. In the case of RDDr, the strands are mixed with combustrion air to heat them up and drive off excess water while in a RDB the strands are coated with a fine dispersion resin droplets.
The objective of drying is to produce strands of uniform moisture content while that of blending is to achieve a uniform resin distribution on both sides of all strands. In both cases it is desirable to minimze strand breakage. During blending, it is quite common for some strands to be almost devoid of resin. These resin poor areas correspond to zones of poor bonding in the product; a common means of addressing these weak zones is to increase the resin mass deposited onto the strands. This will work to a point, but it increases the cost of the finished board. A better solution is to apply only the required amount of resin. The cost saving from such an optimization would be quite significant with saving of approximately $1.3 million dollar per plant in Canada if the resin content is reduced by only 3%. As Canada has 25 plants the savings would be over $30 million dollars.
It is the intent of this project to simulate the continuous RDDR and RDB processes using Discrete Element Modeling (DEM). The Wood Composites Group at UBC was the first to use a DEM for the modeling of RDB for batch blending. They performed trials in their glass front, lab-scale blender and simulated the motion of strands in an identical, virtual blender using a DEM. The result was a model that closely matched the lab results in terms of strand motion.
Program
Discovery Grants Program - Individual
Recipient
Location
British Columbia, Canada
Recipient Type
Academia
Type
Grant
Source
NSERC's Awards Data
As published
Application id
239109-2010
Name nom
Smith, Gregory
Department département
Wood Science
Organization id
2
Institution établissement
University of British Columbia
Province en
British Columbia
Province fr
Colombie-Britannique
Country en
CANADA
Country fr
CANADA
Fiscal year exercice financier
2010
Competition year année de concours
2010
Award amount
20000
Program id
RGPIN
Program name en
Discovery Grants Program - Individual
Program name fr
Programme de subventions à la découverte - individuelles
Group en
Discovery grants programs
Group fr
Programmes de subventions à la découverte
Committee code
1511
Committee name en
Materials and Chemical Engineering
Committee name fr
Génie chimique et des matériaux
Area of application code
1208
Area of application group en
Advancement of knowledge
Area of application group fr
Avancement des connaissances
Area of application en
Materials sciences
Area of application fr
Sciences des matériaux
Research subject code
2000
Research subject group en
Materials science and technology
Research subject group fr
Science et technologie des matériaux
Research subject en
Materials science and technology
Research subject fr
Science et technologie des matériaux
Partie
1
Nb partie
5
Application title
Development of discrete element models for continious rotary drum drying and blending for osb
Keyword
NSERC
Application summary
Oriented Strand Board (OSB) is the dominant structural panel in today's North American residential construction market. These strand-based wood products can be found everywhere from sheathing on exterior walls to the headers used to span garage door openings and specialty studs used behind kitchen cabinets.
OSB is made from thin strands that are first dried in a Rotary Drum Dryer (RDDr) and then coated with resin in a Rotary Drum Blender (RDB). Both RDDr and the RDB are, as their names imply, large drums that rotate about their long axis. In the case of RDDr, the strands are mixed with combustrion air to heat them up and drive off excess water while in a RDB the strands are coated with a fine dispersion resin droplets.
The objective of drying is to produce strands of uniform moisture content while that of blending is to achieve a uniform resin distribution on both sides of all strands. In both cases it is desirable to minimze strand breakage. During blending, it is quite common for some strands to be almost devoid of resin. These resin poor areas correspond to zones of poor bonding in the product; a common means of addressing these weak zones is to increase the resin mass deposited onto the strands. This will work to a point, but it increases the cost of the finished board. A better solution is to apply only the required amount of resin. The cost saving from such an optimization would be quite significant with saving of approximately $1.3 million dollar per plant in Canada if the resin content is reduced by only 3%. As Canada has 25 plants the savings would be over $30 million dollars.
It is the intent of this project to simulate the continuous RDDR and RDB processes using Discrete Element Modeling (DEM). The Wood Composites Group at UBC was the first to use a DEM for the modeling of RDB for batch blending. They performed trials in their glass front, lab-scale blender and simulated the motion of strands in an identical, virtual blender using a DEM. The result was a model that closely matched the lab results in terms of strand motion.