Grant: Discovery Grants Program - Individual
University of Toronto
$39,000.00
Improving aerodynamic control strategies for low Reynolds number airfoils
EF 2024-25
Résumé
Standard airfoil profiles are designed for optimal aerodynamic performance at high speed based on the Reynolds number, a ratio of flow inertia and fluid viscosity. For example, a Boeing 747 operates at a Reynolds number of approximately 80 million while an insect might have a Reynolds number of roughly 1000. Operating airfoils at low Reynolds number (below one million) is of interest in many engineering applications including low-speed unmanned aerial vehicles, wind turbines, and low-speed/high-altitude aircraft; however, airfoil performance is significantly reduced. For wind turbine installation in most of Ontario, this is a concern as there are limited locations with high enough wind speeds to produce power. Flow separation on airfoils, the detachment of the boundary layer from a surface into a wake, is particularly prevalent at low Reynolds numbers due to the interaction of the laminar boundary layer on the suction surface where flow pressure increases in the flow direction (an adverse pressure gradient). The momentum contained in the boundary layer is often unable to withstand the forces imposed by the adverse pressure gradient, which causes the flow to separate.
The use of periodic excitation, i.e., active flow control, applied locally at the surface to mitigate flow separation and restore the aerodynamic performance of stalled airfoils is a technique that has been applied with varying degrees of success for several years. Because these devices are flat to the airfoil surface, no geometric drag is introduced. Since 2005, our lab has been studying the synthetic jet actuator (SJA) as a candidate control method. The SJA has a vibrating diaphragm mounted in a cavity with an orifice/slot leading to the surface where control is desired. Deformation of the diaphragm causes the working fluid to be alternately ingested and expelled by the cavity, thereby adding momentum (but not mass) to the flow.
The main difficulties faced with this technology and, particularly the approach proposed here, is that despite the relatively small size of typical actuators, they are still quite large, heavy and difficult to maintain.
It is proposed to:
�Design synthetic jet actuators arrays with commercial MEMS SJAs capable of being placed onto an airfoil along with sensing elements to allow feedback control.
�Characterize and compare their behavior numerically and experimentally.
This will be done using whole field experimental measurements to test the MEMS SJA and numerical modeling of the effect of the synthetic jets using high-fidelity computational codes, Large Eddy Simulation, to guide design. The work benefits from past data in the lab.
Reducing SJA size would allow inexpensive MEMS components to be easily placed and replaced as necessary. The cost of the commercially available devices would be much less as they can be fabricated in large numbers using automated technologies and it would be possible to perform maintenance quickly and reliably.
Programme
Discovery Grants Program - Individual
Bénéficiaire
Emplacement
Ontario, Canada
Type de bénéficiaire
Academia
Type
Grant
Source
NSERC's Awards Data
Tel que publié
Application id
RGPIN-2022-03071
Name nom
Sullivan, Pierre
Department département
Mechanical and Industrial Engineering - Mechanical and Industrial Engineering
Organization id
31
Institution établissement
University of Toronto
Province en
Ontario
Province fr
Ontario
Country en
CANADA
Country fr
CANADA
Fiscal year exercice financier
2024
Competition year année de concours
2022
Award amount
39000
Program id
RGPIN
Program name en
Discovery Grants Program - Individual
Program name fr
Programme de subventions à la découverte - individuelles
Group en
DISCOVERY RESEARCH
Group fr
RECHERCHE AXÉE SUR LA DÉCOUVERTE
Committee code
1512
Committee name en
Mechanical Engineering
Committee name fr
Génie mécanique
Area of application code
703
Area of application group en
Transportation systems and services
Area of application group fr
Services et systèmes de transport
Area of application en
Aerospace
Area of application fr
Aérospatial
Research subject code
2201
Research subject group en
Fluid mechanics
Research subject group fr
Mécanique des fluides
Research subject en
Turbulence
Research subject fr
Turbulence
Field of research list names en
Not available
Field of research list names fr
Non disponible
Socioeconomic objective list names en
Not available
Socioeconomic objective list names fr
Non disponible
Application title
Improving aerodynamic control strategies for low Reynolds number airfoils
Keywords
aerodynamic control; dynamic mode decomposition; snapshot pod; computational fluid dynamics; particle image velocimetry; turbulence
Application summary
Standard airfoil profiles are designed for optimal aerodynamic performance at high speed based on the Reynolds number, a ratio of flow inertia and fluid viscosity. For example, a Boeing 747 operates at a Reynolds number of approximately 80 million while an insect might have a Reynolds number of roughly 1000. Operating airfoils at low Reynolds number (below one million) is of interest in many engineering applications including low-speed unmanned aerial vehicles, wind turbines, and low-speed/high-altitude aircraft; however, airfoil performance is significantly reduced. For wind turbine installation in most of Ontario, this is a concern as there are limited locations with high enough wind speeds to produce power. Flow separation on airfoils, the detachment of the boundary layer from a surface into a wake, is particularly prevalent at low Reynolds numbers due to the interaction of the laminar boundary layer on the suction surface where flow pressure increases in the flow direction (an adverse pressure gradient). The momentum contained in the boundary layer is often unable to withstand the forces imposed by the adverse pressure gradient, which causes the flow to separate.
The use of periodic excitation, i.e., active flow control, applied locally at the surface to mitigate flow separation and restore the aerodynamic performance of stalled airfoils is a technique that has been applied with varying degrees of success for several years. Because these devices are flat to the airfoil surface, no geometric drag is introduced. Since 2005, our lab has been studying the synthetic jet actuator (SJA) as a candidate control method. The SJA has a vibrating diaphragm mounted in a cavity with an orifice/slot leading to the surface where control is desired. Deformation of the diaphragm causes the working fluid to be alternately ingested and expelled by the cavity, thereby adding momentum (but not mass) to the flow.
The main difficulties faced with this technology and, particularly the approach proposed here, is that despite the relatively small size of typical actuators, they are still quite large, heavy and difficult to maintain.
It is proposed to:
�Design synthetic jet actuators arrays with commercial MEMS SJAs capable of being placed onto an airfoil along with sensing elements to allow feedback control.
�Characterize and compare their behavior numerically and experimentally.
This will be done using whole field experimental measurements to test the MEMS SJA and numerical modeling of the effect of the synthetic jets using high-fidelity computational codes, Large Eddy Simulation, to guide design. The work benefits from past data in the lab.
Reducing SJA size would allow inexpensive MEMS components to be easily placed and replaced as necessary. The cost of the commercially available devices would be much less as they can be fabricated in large numbers using automated technologies and it would be possible to perform maintenance quickly and reliably.